Magigoo

Sort By:  
All you need for sure adhesion of Nylon based filament 3D prints
23.45€
All you need for sure adhesion of 3D prints
18.75€
Magigoo PA (Original PA)

Magigoo PA

 

WHAT: MAGIGOO PA is designed for professional use, to work exclusively with Polyamide filaments. The part should be relatively easy to remove once it cools and the glue residue should also be easily cleaned off.

 

WHY:

PA (polyamide) describes a group of polymers with an amide repeat unit. Generally in the FDM industry there are 3 main types of PA which include PA12, PA6,6 and PA6, sometimes these materials can be either grafted with other polymers or else reinforced with glass or carbon fibres. Generally nylons exhibit high strength, toughness, elasticity, wear resistance, chemical resistance and thermal resistance and are widely sought in various industrial applications.

 

Nylon filaments prove to be challenging materials for FDM printing due to their lower adhesion to conventional 3D-printing build surfaces and their higher tendency to warp. Furthermore there are several classes of PA filaments each behaving differently. MAGIGOO-PA is a specialized solution for FDM printing of PA filaments which was developed to work with a wide number of PA types

 

HOW:

MAGIGOO PA has been designed and tested to work with different PA and fiber reinforced filament brands.

  • Shake the bottle.
  • Apply to the desired area by pressing the nib on the bed (activating the inner valve) and spreading as needed.
  • Print according to the filament/printer manufacturers recommendations
  • Allow to cool and Remove. The print should pop right off
  • Clean - Use a damp cloth to wipe off.

 

SAFETY:

Using this product with other than PA type filaments might cause over adhesion and damage your build surface.

 

Tips:

For larger prints a 20 mm brim is recommended

In cases of excess adhesion, it is recommended to wet print bed with a small amount of water slowly work it below the part, this should make part removal easier

All you need for sure adhesion of Nylon based filament 3D prints
23.45€
Magigoo Original (Original 50 ml)

Product description:

 

 

All you need for sure adhesion of 3D prints Magigoo is an easy to use 3D printing adhesive designed to address 'the first layer not sticking problem'. Magigoo ensures a strong adhesion to the hot plate. But the magic starts when printing is ready: just wait for the plate to cool down and then remove your prints with just a finger flick! In addition, Magigoo helps to prevent warping. Isn't it magic? Regardless of you being a hobbyist or professional - it is extremely rewarding to have a 30 hour print complete without any warping and having it release easily once cooled.

  • Over 100 applications
  • ABS, PLA, PETG, HIPS, ASA, TPU
  • Easy application
  • Easy release
  • Easy clean
  • No smell
  • Non-toxic
  • No additional tools needed
  • Easy to transport
  • Nicer print finish

 

Main Features 

  • Easy application: applying Magigoo is as easy as child's play. Shake, press, apply. Spread on an active printing area only. No need to cover the whole surface
  • Easy-release: Magigoo adhesive properties are designed to release the 3D print once the build plate has cooled.
  • Easy-clean: Magigoo is easily cleaned with water.
  • Long-lasting: Magigoo last for 100+ average prints.
  • Odorless and safe: Magigoo is safe to use - be it in a closed room or educational workshop with kids.

 

Important note : The applicator has an active spring valve, which activates when applicator is pressed against the build plate. Please do not press the bottle as "ketchup bottle" , otherwise  the applicator may pop off. Bottle may be slightly squeezed,  only when the nib is pressed against the bed and it may be necessary only if bigger flow is required. Bottle must not be squeezed when cap is off any other time as it may result in glue popping out of the bottle. 

 

All you need for sure adhesion of 3D prints
18.75€
Per Page      1 - 2 of 2
  • 1